Loading...
 

SLIM X 13 and SLIM 13E

BlackTrax System Overview  »  BTSystem Components  »  BTSensors  »  SLIM X 13 and SLIM 13E

SLIM X 13 and SLIM 13E Diagram  SLIM 13E Diagram

 

Product ID

  • SLIM X 13 Model number: CAM-PAK-SMX
  • SLIM 13E Model number: CAM-CAM-S13

 

Physical Characteristics

  • Mounting: 0.635 cm (1/4”)-20 tripod thread
  • Operating temperature: 0°C to +51°C (32°F to 123.8°F)
    • Note: Warm-up time of 30 minutes is recommended for optimal tracking performance. Watch out for condensation when used in temperatures below 0°C.
  • Case: Aluminum and Polycarbonate
  • Width: 6.86 cm (2.7”)
  • Height: 6.86 cm (2.7”)
  • Depth: 2.3 cm (0.9”)
  • Weight: 320 g (11.29 oz)

 

Lens & Filter

  • Stock lens: 5.5 mm F#1.8 (wide band AR coated)
    • Horizontal FOV: 56°
    • Vertical FOV: 46°
  • Optional Lens: 8.0 mm F#1.8 (wide band AR coated)
    • Horizontal FOV: 42°
    • Vertical FOV: 34°
  • Optional Lens: 3.5 mm F#1.8 (wide band AR coated)
    • Horizontal FOV: 82°
    • Vertical FOV: 70°
  • Adjustable focus with wave spring assist
  • 850nm band-pass filter
  • 850nm (Infrared) / 700nm (Visible) Filter Switcher
    • Note: BTSensors that have the "NFS" label printed on the side do not have the Filter Switcher.

 

Image Sensor

  • Resolution: 1280 × 1024
  • Frame Rate: 30–240 FPS (100 FPS average usage)
  • Accuracy: +/-0.3 mm
  • Latency: 4.2 ms
  • Shutter type: global
  • Shutter speed:
    • Default SLIM 13E: 0.5 ms (500 µs)
    • Default SLIMX 13: 0.25 ms (250 µs)
    • Minimum: 0.01 ms (10 µs)
    • Maximum: 3.9 ms (3,900 µs) at 240 FPS

 

Input/Output & Power

Data: Ethernet
Synchronization: Ethernet
Power: (PoE) 8.0 watts 

 

Sensor Status

Front LCD Status

In normal operation mode, the front LCD panel of the SLIM Series will display the sensor's ID number to easily identify the unit.

When updating the software on your BTServer, the sensor may need a firmware update in order to communicate to the new version. Firmware updates are automatic when starting the connection to the BTServer. Reverting back to an older version of the firmware is also an automatic process.

The front LCD panel will display the flashing progress during the firmware update. The front LCD panel will go from 0 to 99 to indicate the flashing progress.

Front Light Status

The Slim Series sensors have a front LED status light to indicate their current state in relation to the BTServer. The following table lists the default status light colors.

FrontStatusLight  

Back Light Status

The Slim Series sensors also have a status indicator on the back panel and indicates the state of the sensor only. When updating the software on your BTServer, the sensor may need a firmware update in order to communicate to the new version. Firmware updates are automatic when starting the connection to the BTServer. If you revert back to an older version of the firmware as well. This process is automatic.

BackStatusLight  

BTSensor Functions

BTSensors are used to view BTBeacon positions in the Space. A BTBeacon's position in 3 dimensions (X, Y, and Z) can be determined when two or more BTSensors simultaneously have a direct line-of-sight to a connected Stringer’s LED. This information is then sent to the BTServer.

 

Attention:

  • The switch must provide consistent power to every port simultaneously in order to power each sensor.
  • Standard PoE switches must provide a full 15.4 watts to every port simultaneously.
  • Note that PoE Midspan devices or power injectors are not suitable for Ethernet camera systems.

 

History